HOBBYWING COMBO MAX10 SCT ESC 3660SL 3200KV MOTOR
The MAX10 SCT ESC is applicable to various 1/10th scale vehicles like trucks, short-course trucks, monster trucks, and etc. Built with the most rugged and high-quality components and coupled with cutting-edge firmware, the EzRun MAX10 SCT is able to deliver unmatched power and performance for even the most hardcore of racing applicatinos, but is also responsive enough to protect itself from damage due to overloading due to physical abuse, overuse or even human error.
With incredible acceleration capabilities and a rock-solid, stable output, the MAX10 SCT can handle instant full-torque start-ups for wheelies, high-speed racing on straightaways and powering through the bumpiest terrian. The user will have the choice of adusting the ESC parameters as per his perference and ability.
The waterproof and dust-proof design allows the MAX10 SCT to be used in all weather conditions without any issue of damage caused to the ESC from water or dust.
You can upgrade the MAX10 SCT with the HobbyWing USB LINK software, a multifunction LCD program box and a laptop. HobbyWing updates its ESC firmware regularly giving you upgraded features more often when available.
Hobbywing EzRun MAX10 SCT Features:
- High Reliability & Durability
- Great Flexibility & Versatility
- Advanced and Secure Electronic Switch
- Applicable to All Weather Conditions
- Innovative Filter Capacitor Thermal Protection
- Regular Firmware Updates Free of Charge
Spec Check:
- Scale: 1/10th
- Brushed/Brushless: Brushless
- Sensored/Sensorless: Sensorless
- Waterproof: Yes
- Cont./Peak Current: 120A/760A
- Input: 2-4S LiPo/6-12 Cells NiMH
- BEC Output: Switch Mode:6V/7.4V,3A
- Input Wires: Red-12AWG-200mm*1/Black-12AWG-200mm*1
- Output Wires: Black-12AWG-200mm*3
- Input Connectors: No
- Output Connecotors: 4.0 Bullet Connectors (Female)
- Fan Size: 25.0x25.0x10.0mm
- Fan Voltage Range: 5-7.4V
- WiFi Module: Supported
- Program Port: FAN/Program Port
- Size: 49.0x39.5x34.7mm
- Weight: 105g
The HobbyWing EzRun 3660 G2 motor features an Innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented). It has low cogging effect and torque pulsation for improved control feel around corners. The built-in temperature sensor and sensor port protect the motor from damage due to overheating when pairing with an EzRun Max10/Max10 SCT ESC.
HobbyWing EzRun 3660 G2 3200KV SL Motor Features:
- Innovative 4-pole-8-magnet "staggered pole" rotor
- Built-in temperature sensor and sensor port
- O-ring seal fitted between the front end bell and motor case
- Special design motor case (the end attaches to the front end bell) isolates inner coils from outside to protect winding from being damaged by overlong screws
- Special technology for temperature control for less heat and more efficiency (efficiency rate of up to 90%)
- CNC machined aluminium housing, high purity copper windings and advanced rotor structure
- Rebuild-able design for easy routine maintenance
Spec Check:
- Scale: 1/10th
- Brushed/Brushless: Brushless
- Sensored/Sensorless: Sensorless
- Pole Count: 4
- KV Rating: 3200
- LiPo Cells: 2-3S
- No-load Current(A): 4.9
- Timing: 0 Degrees(Fixed)
- O.D.(mm): 36.00
- Length (mm): 60.00
- Shaft Diameter (mm): 5.0
- Weight (g): 262
Hi , I plan to do a brushless conversion on my Arrma typhon 4x4 mega 550 and I wondered if this combo will fit , is the motor shaft compatible etc . Thanks . John
Asked by John on 2nd January 2020
Yes these will fit and work well - however they do have a 5mm motor shaft, so you'll just need a new pinion with a 5mm shaft diameter.
Answered by: Ben @ Wheelspin Models
Would this be a suitable upgrade for an ftx bugsta ( currently brushed), or would one of the other kv motors be better??
Thanks
Asked by Gavin on 29th February 2020
That would work well in the Bugsta
Answered by: Ben @ Wheelspin Models
Would this work on a slash 2wd converting from brushed ? I
Asked by Aaron on 9th April 2020
Yes, that would work.
Answered by: Ben @ Wheelspin Models
How do I get a connector put on this?
Asked by Seb on 22nd May 2020
You can solder on your choice of connector
Answered by: Ben @ Wheelspin Models
Hi will this work as an upgrade for the summit 1/8 scale ? And would I need to change pinion gear if it does
Asked by Matt on 20th July 2020
No this is for a 1/10 car you need a 1/8 system due to the size and weight of the truck.
Answered by: Anthony @ Wheelspin Models
Hi what battery should I be get for this. Bit new to this thanks
Asked by Paul on 21st August 2020
A good 2S battery say VZ0317 or PEK00545 would work nicely
Answered by: Ben @ Wheelspin Models
Would this be a good upgrade to make my team associated DB10 faster currently running 2s
Asked by Jamie on 23rd August 2020
Yes that should work nicely in there
Answered by: Ben @ Wheelspin Models
Whats the minimum C rating for the esc?
Asked by Jack on 19th September 2020
It's not quoted.
120A would be a theoretical 11C at 3S - so let's say minimum 25C to be on the safe side
Answered by: Ben @ Wheelspin Models
I have a stock 2wd Traxxas Raptor and zero experience with RC stuff. Is this a fairly easy swap for the stock system? Or do I need to solder stuff etc?
Asked by Matt on 30th September 2020
It's fairly straightforward to bolt the new motor in, but you would need to solder on your battery connectors onto the ESC
Answered by: Ben @ Wheelspin Models
Hi how would this compare if I switched it for the vxl system in my rustler
Asked by Charlie on 11th December 2020
I'd say it's comparable to your TRX Velinion 3S sytem
Answered by: Ben @ Wheelspin Models
Does this brushless motor require lipo batteries or are the normal NiMh batteries OK to use?
Asked by Mr Brendon J Moss on 14th December 2020
You can use either - but you will have better performance on LiPo
Answered by: Ben @ Wheelspin Models
Can I run this on 4s
Asked by Charlie on 15th December 2020
It would depend on your setup, but I'd advise 3S is probably your max on this
Answered by: Ben @ Wheelspin Models
Hi what programming card works with this
Asked by Charlie on 16th December 2020
The HW30502000 program card works with these
Answered by: Ben @ Wheelspin Models
HW86020010 Does this work with this combo and what pinion will pair with a traxxas spur
Asked by Charlie on 17th December 2020
I believe it's the HW30502000 program card you need for this.
These are a 5.0mm shaft diameter on the motor, so it will just depend which Traxxas you have?
Answered by: Ben @ Wheelspin Models
Hi
Would this combo take a 4s Lipo
Regards
Andy
Asked by Andy Spencer on 17th January 2021
3S would be recommended max on these
Answered by: Ben @ Wheelspin Models
Hi, I have an old(ish) ECX Ruckus truck (1/10, 2WD). It currently runs on the standard Spektrum ESC and 15T brushed motor and 7.2 or 8.4v NiMh batteries.
Would this ESC and motor be a suitable alternative (maybe with a smaller pinion?)
The current batteries are showing their age, and the motor sometimes gets very hot (one burnt out).
Thanks
Rich
Asked by Richard Morris on 9th February 2021
This would fit and work well - just bear in mind this motor has a 5mm shaft so you would need a new 5mm pinion
Answered by: Ben @ Wheelspin Models
Hi is this ok for a straight forward replacement for existing standard combo in my typhon 3s blx...thanks
Asked by Andrew on 26th February 2021
Yes that should work - just bear in mind these have a 5mm motor shaft though
Answered by: Ben @ Wheelspin Models
Hi, I would like to put this combo in my grandsons Slash 4x4, can I use a 2S 5500mah 50C lipo on this combo, thanks
Asked by Andrew on 10th November 2021
Yes this would be fine for that model of car.
Answered by: Anthony @ Wheelspin Models
Hi, would this be a suitable upgrade for Absima AB3.4 running on 3s lipo? Thanks.
Asked by Stuart Claridge on 2nd April 2022
You will struggle to get a pinion to fit the motor due to the 5mm motor shaft and the gearing pitch on that car.
You would be better looking at the normal version not the SCT version. HW38010203
Answered by: Si @ Wheelspin Models
Would this be suitable for the traxxas hoss given it’s 10th scale
Asked by Michael on 3rd June 2022
No that is not a big enough motor , the one in the hoss is a 540 xl motor so is longer which adds more torque required for bigger trucks.
Answered by: Steve W @ Wheelspin Models
Can you use the hobbywing Ota Wi-Fi
Asked by Ashley on 17th September 2022
No this needs this one HW30502001
Answered by: Steve W @ Wheelspin Models
Will this be suitable for a brushless upgrade to my Vorteks Boost? I’ve preordered the transmission upgrade.
Asked by Mark on 13th October 2022
Yes that will be fine but you will need a pinion gear to suit.
Answered by: Steve W @ Wheelspin Models
Would this combo fit and be good for the FTX Ramraider
Asked by Christopher on 2nd February 2023
Yes that will fit but you will need a pinion 32 dp with a 5mm shaft on it and a xt90 to deans adaptor to use batteries with deans on them.
Answered by: Steve @ Wheelspin Models
