HOBBYWING COMBO MAX10 ESC 3652SL 5400KV MOTOR
Built with high-quality components and coupled with cutting-edge firmware, the MAX10 is able to deliver unmatched power and performance for even the most extreme racing applications, but it is also responsive enough to protect itself from damage due to overloading due to physical abuse, overuse or even human error.
The MAX10 features an electronic switch with a lifespan of over 50000 on/off cycles, housed in a completely waterproof, dust-proof and shock-resistant design.
The waterproof and dust-proof design allows the MAX10 to be used in all weather conditions without any issue of damage caused to the ESC from water or dust.
The built-in switch mode BEC with a maximum output of 6A and voltage adjustable between 6V and 7.4V allows the use of various high voltage servos.
When pairing the MAX10 with a Hobbywing matching motor (i.e. EzRun 3652/3660 G2 motor), the temperature sensor cable on the ESC will monitor the motor temperature and protect the motor from irreversible damage due to overheating in real time.
Hobbywing EzRun MAX10 ESC Features:
- Capacitor Thermal Protection
- High Reliability & Durability
- Super Internal BEC
- Applicable to All Weather Conditions
- Advanced and Secure Electronic Switch
- Regular Firmware Updates
Spec Check:
- Scale: 1/10th
- Brushed/Brushless: Brushless
- Sensored/Sensorless: Sensorless
- Waterproof: Yes
- Cont./Peak Current: 60A/450A
- Input: 2-3S LiPo/6-9 Cells NiMH
- BEC Output: Switch Mode 6V/7.4V,3A
- Input Wires: Red-14AWG-200mm*1/Black-14AWG-200mm*1
- Output Wires: Black-14AWG-200mm*3
- Input Connectors: No
- Output Connecotors: 3.5 Bullet Connectors (Female)
- Fan Size: 25.0x25.0x10.0mm
- Voltage Range: 5-7.4V
- Powered by BEC
- SET Button on ESC: Supported
- LED Program Box: Supported
- LCD Program Box: Supported
- WiFi Module: Supported
- Size: 39.4x32.8x23.1mm
- Weight: 67.8g
The HobbyWing EzRun 3652 G2 motor features an Innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented). It has low cogging effect and torque pulsation for improved control feel around corners. The built-in temperature sensor and sensor port protect the motor from damage due to overheating when pairing with an EzRun Max10/Max10 SCT ESC.
HobbyWing EzRun 3652 G2 5400KV SL Motor Features:
- Innovative 4-pole-8-magnet "staggered pole" rotor
- Built-in temperature sensor and sensor port
- O-ring seal fitted between the front end bell and motor case
- Special design motor case (the end attaches to the front end bell) isolates inner coils from outside to protect winding from being damaged by overlong screws
- Special technology for temperature control for less heat and more efficiency (efficiency rate of up to 90%)
- CNC machined aluminium housing, high purity copper windings and advanced rotor structure
- Rebuild-able design for easy routine maintenance
Spec Check:
- Scale: 1/10th
- Brushed/Brushless: Brushless
- Sensored/Sensorless: Sensorless
- Pole Count: 4
- KV Rating: 5400
- LiPo Cells: 2S
- No-load Current(A): 7.2
- Timing: 0 Degrees(Fixed)
- O.D.(mm): 36.00
- Length (mm): 52.00
- Shaft Diameter (mm): 3.175
- Weight (g): 217
Two Simple UK Delivery Options
Royal mail at £3.95, or Express at £6.95.
Full details at checkout.
Some items cannot be sent via Royal Mail due to their restrictions.
We Ship Worldwide!
To see shipping costs simply add the item to your basket and choose your country from the drop down list on the view cart page.
No product reviews yet!
will this unit fit onto the FTX Kenyon 4X4 RTR 1:10 XL Trail Crawler FTX 5563
Asked by Stuart Beddows on 6th September 2019
Yes, that would fit the FTX Kanyon as it uses a standard 540 size motor.
Answered by: Ben @ Wheelspin Models
Will this be ok in my traxxas bandit to replace the brushed set up
Asked by Wayne on 3rd February 2020
Yes that would work well in a Bandit
Answered by: Ben @ Wheelspin Models
Does the Hobbywing MAX10 SCT ESC Combo With 3652Sl 5400KV Brushless Motor come with a tamiya connector on the esc.
Thanks
Asked by Harry Widdowson on 2nd April 2020
These do not come with connectors
Answered by: Ben @ Wheelspin Models
Is this a good crawler combo if not is there any better ones
Asked by Liam on 23rd June 2020
Not really much good for crawling - I'd look at the hobbywing AXE systems instead.
Answered by: Ben @ Wheelspin Models
Would this Brushless set up be able to replace my brushed set up on my jumpshot st v2? And if it would would it come with deans connectors?
Asked by Cameron C on 30th June 2020
Yes that should work OK in there.
These do not come with connectors but you can easily solder deans on
Answered by: Ben @ Wheelspin Models
Getting back into rc cars after a 30 year break! Would this combo be good for a cat xls rerelease?
Asked by Ant on 30th July 2020
It would fit and work well - but you'd want to make sure you have the U7236 transmission upgrade in the CAT XLS to run a high power motor like this
Answered by: Ben @ Wheelspin Models
Can i use 3s lipo with this setup?
Asked by Darren on 3rd January 2021
In theory yes, however it's a high KV motor so would need to be a very light chassis and geared accordingly so as not to cook the motor/ESC
Answered by: Ben @ Wheelspin Models
Hi
Could you supply the combo with deans connectors please?
Asked by Geoff Gostage on 3rd March 2021
Afraid we don't have these with deans pre-soldered
Answered by: Ben @ Wheelspin Models
what would you say is the best motor here for 2s drag racing?
Asked by Alex on 11th March 2021
I guess for drag racing you want the higher KV motors such as this.
Just keep an eye on temperatures and gear accordingly
Answered by: Ben @ Wheelspin Models
Hi, what battery connector type is fitted to this ESC?
Asked by Tim on 2nd June 2021
These do not have a connector fitted
Answered by: Ben @ Wheelspin Models
Is this esc compatible with the hobby wing max10 3300kv motor? As i e bought this set up and need a 3300 kv motor to resolve a cogging issue many thanks connor
Asked by Connor on 19th July 2021
Yes, this is the same ESC as HW38010203 just a different motor
Answered by: Ben @ Wheelspin Models
Is this suitable for the Tamiya TT02?
Asked by Connor on 22nd October 2021
It would be yes, just stick to a 7.4 volt battery as a maximum.
Answered by: Anthony @ Wheelspin Models
Would this combo suit a Kyosho turbo scorpion?
Asked by Roger Clemo on 22nd November 2021
Yes this would be great , just run this car on a 7.4v and not an 11.1v battery.
Answered by: Anthony @ Wheelspin Models
Hi, looking at this bundle for my FTX vantage as I want alot of speed. Just wanted know the main differences between the other hobbywing 1/10 bundles and which one u would recommend for atleast 60mph+
Asked by Lewis on 29th June 2022
That will only run on 2s lipo and will get very hot i would look at this HW38010203
The main difference between the 3660 combos and the 3652 is the 3660 motors have 5mm shafts so you will not find a pinion gear to fit those and work in the carnage the 3652 have 3.17mm motor shafts aso all you pinions will fit on that.
Answered by: Steve W @ Wheelspin Models
Looking for a max10 set up that will work in a tamiya plasma edge 4x4 could you point me in the right direction please will i need to go for a lower kv as the trucks heavier and 4x4? Ie 4000kv? What would you recommend? Or would you recommend a totally different motor set up? Would like to stick with hobby wing if i can. Many thanks connor
Asked by Connor Doran on 9th November 2022
Yes for off road use we would recommend a KV rating no higher that 3500 with that car.
Have a look at HW38010203
Answered by: Si @ Wheelspin Models
Would this combo fit in my Associated RB10
Asked by Steve on 20th January 2023
This would fit and work in that car, the ESC is on the larger size so you may need to get it positioned in a place to get the bodyshell on the car.
Answered by: Si @ Wheelspin Models
Would this motor comb be ok for a Associated RC10B6.4 Team Kit?
Asked by John Huett on 24th February 2023
It would work fine but is not something that could be used for racing.
Answered by: Steve @ Wheelspin Models
Recommendation for 4x4 stampede please.
Asked by Mark Bray on 1st April 2023
Yes you will need this one HW38010200 and a pinion gear with a 5mm shaft like this one AR310425
Answered by: Steve @ Wheelspin Models
