EUR
£ GBP
$ USD
Oracover Air Medium 2M Chrome Purple (096)
Brand: Oracover
Part No: ORA321-096-002
Out Of Stock
Request Stock NotificationOracover Air Medium 2m Chrome Purple (096) is an ultra-light polyester covering film designed for minimal-weight constructions, including indoor flyers, park flyers, blimps and airships. This ORACOVER AIR variant has no adhesive layer and is intended for use with a brushed-on hotmelt adhesive for secure bonding. Colour-fast pigmentation resists bleeding at seam edges when ironing, while the striking Chrome Purple finish adds a premium look. Part number: ORA321-096-002.
Key Features
- Colour-fast film with no bleeding at ironed seams
- Ultra-light ORACOVER AIR MEDIUM (approx. 34 µm) for weight-critical builds
- No adhesive layer; use with ORACOVER AIR Hotmelt Adhesive
- Suggested use for indoor and park flyers, blimps and airships
Dimensions & Material
- Width: 600mm
- Length: 2,000mm (2m)
- Material: Polyester
- Colour: Chrome Purple
Recommended Accessories
- ORACOVER AIR Hotmelt Adhesive (100 ml) for brushing onto the surface
- ORACOVER AIR Special Thinner to restore brushing viscosity if needed
- Approximate coverage: about 1 tin per 1 m²
Application Notes
- Sand the wood thoroughly and remove dust
- Stir the adhesive well
- Apply 1–2 thin, even coats by brush
- Allow to dry at least 10 hours (do not resand)
- Iron on ORACOVER AIR as with standard thermal-shrink coverings
Secured by Stripe
Key Features
- Colour-fast - there is no 'bleeding' at the edges when ironing over seams.
-
The covering for light constructions.
Wherever minimum weight is demanded, wherever weight has to be reduced to its limits, ORACOVER® AIR is the product to be applied.
Whether indoor flyers, park flyers, blimps or airships are to be built, ORACOVER® AIR will do the covering job.
In contrast to regular ORACOVER®, ORACOVER® AIR has no adhesive layer.
The hotmelt adhesive is to be brushed onto the surface.
ORACOVER® AIR MEDIUM (approx.34 µm), for blimps and airships up to 4 m length.
RECOMMENDED ACCESSORY :
ORACOVER® AIR Hotmelt Adhesive ORACOVER AIR Adhesive (100 ml) Unstable wood fibres can become insecure and can rip off due to the weight. The consequences would be wrinkling and in the worst case the complete peeling off of the fabric.
Our tip: For an optimal pre-treatment of your wood surface we recommend to coat the surfaces to be ironed with ORACOVER® AIR Hotmelt Adhesive.
The ORACOVER® AIR Hotmelt Adhesive penetrates the wood and sticks together the loose wood fibres of the heartwood.
With that you reach an excellent three-D adhesion of the ORACOVER® AIR film with the surface.
With the ORACOVER® AIR Hotmelt Adhesive you do not need a further pre-treatment of the wood anymore.
Application of the ORACOVER® AIR Hotmelt Adhesive:
1. Sand your wood completely and remove the swarf (vacuum).
2. Stir up well the contents of the tin.
3. Apply the ORACOVER® AIR Hotmelt Adhesive 1 – 2 times thinly and evenly by using a brush.
4. Let the adhesive dry overnight, however at least 10 hours. (Please do not resand).
5. Cover your model as always with the thermal shrink fabric covering ORACOVER® AIR.
Productivity: approx. 1 tin / 1m² Unsuitable for surfaces which are not resistant to organic solvents.
ORACOVER® AIR SPECIAL THINNER If our adhesives should dry a little bit in open containers, the adhesive can be adjusted again to brushing viscosity with the corresponding thinner.
Weights & Dimensions
| Shipping Weight | 0.09kg | 0.20lbs |
| Product Width | 600mm | 23.62in |
| Product Length | 2,000mm | 78.74in |
- Colour: Chrome Purple
- Material: Polyester
Key Info:
- Brand: Oracover
- Part No: ORA321-096-002
- Barcode: 5051121144796
- Material: Oracover
Standard Shipping
£3.95 to most of the UK
Express Shipping
£6.95 to most of the UK
Worldwide Shipping
Available at checkout
Reviews
No specific product reviews yet, why not write one?WRITE A REVIEW
ASK A QUESTION
For more in depth queries, please contact us.