Oracover Magic 2M Red Gold (102)

FEATURES

• ORACOVER® MAGIC is the ultimate product in high tech colour technology. The multi-tone colour changes due to the holographic technology in a vibrant shine.

  ORACOVER®, our leading product for covering RC model airplanes is patented worldwide.

  The unique qualities of ORACOVER®: Permits re-positioning without fear of colour-layer separation - the only covering film giving you a second chance, it is fuel-resistant, tolerates temperatures up to 250°C, can be painted and is highly adhesive. Applied according to instructions there will be no bubbles and no sagging.

   

  RECOMMENDED ACCESSORY : 

  ORACOVER® Hotmelt Adhesive ORACOVER Iron-on adhesive (100 ml) Unstable wood fibres can become insecure and can rip off due to the weight.

  The consequences would be wrinkling and in the worst case the complete peeling off of the fabric.

  Our tip: For an optimal pre-treatment of your wood surface we recommend to coat the surfaces to be ironed with ORACOVER® Hotmelt Adhesive.

  The ORACOVER® Hotmelt Adhesive penetrates the wood and sticks together the loose wood fibres of the heartwood. With that you reach an excellent three-D adhesion of the ORACOVER® film with the surface.

  With the ORACOVER® Hotmelt Adhesive you do not need a further pre-treatment of the wood anymore.

  Application of the ORACOVER® Hotmelt Adhesive:

  1. Sand your wood completely and remove the swarf (vacuum).

  2. Stir up well the contents of the tin.

  3. Apply the ORACOVER® Hotmelt Adhesive 1 – 2 times thinly and evenly by using a brush.

  4. Let the adhesive dry overnight, however at least 10 hours. (Please do not resand).

  5. Cover your model as always with the thermal shrink fabric covering ORACOVER®.

  Productivity: approx. 1 tin / 1m² Unsuitable for surfaces which are not resistant to organic solvents.

  ORACOVER® SPECIAL THINNER If our adhesives should dry a little bit in open containers, the adhesive can be adjusted again to brushing viscosity with the corresponding thinner.

• Re-positioning - the only covering film giving you a second chance without fear of colour-layer separation.
• Fuel-resistant - tolerates temperatures up to 250C and can be painted and is highly adhesive.
• Impeccable finish - follow the application instructions and there will be no bubbles and no sagging.
• Tough - made of genuine polyester ORACOVER is extremely tough and gives your model airplane additional stability. The patented polymerised multi-layer colour-bond is practically indestructible.
• Colour-fast - there is no 'bleeding' at the edges when ironing over seams.
• Foam-safe - can be applied to foam parts without problem as the specially formulated adhesive is already activated at only 80C.

DETAILS

• ORACOVER® MAGIC is the ultimate product in high tech colour technology. The multi-tone colour changes due to the holographic technology in a vibrant shine.

  ORACOVER®, our leading product for covering RC model airplanes is patented worldwide.

  The unique qualities of ORACOVER®: Permits re-positioning without fear of colour-layer separation - the only covering film giving you a second chance, it is fuel-resistant, tolerates temperatures up to 250°C, can be painted and is highly adhesive. Applied according to instructions there will be no bubbles and no sagging.

   

  RECOMMENDED ACCESSORY : 

  ORACOVER® Hotmelt Adhesive ORACOVER Iron-on adhesive (100 ml) Unstable wood fibres can become insecure and can rip off due to the weight.

  The consequences would be wrinkling and in the worst case the complete peeling off of the fabric.

  Our tip: For an optimal pre-treatment of your wood surface we recommend to coat the surfaces to be ironed with ORACOVER® Hotmelt Adhesive.

  The ORACOVER® Hotmelt Adhesive penetrates the wood and sticks together the loose wood fibres of the heartwood. With that you reach an excellent three-D adhesion of the ORACOVER® film with the surface.

  With the ORACOVER® Hotmelt Adhesive you do not need a further pre-treatment of the wood anymore.

  Application of the ORACOVER® Hotmelt Adhesive:

  1. Sand your wood completely and remove the swarf (vacuum).

  2. Stir up well the contents of the tin.

  3. Apply the ORACOVER® Hotmelt Adhesive 1 – 2 times thinly and evenly by using a brush.

  4. Let the adhesive dry overnight, however at least 10 hours. (Please do not resand).

  5. Cover your model as always with the thermal shrink fabric covering ORACOVER®.

  Productivity: approx. 1 tin / 1m² Unsuitable for surfaces which are not resistant to organic solvents.

  ORACOVER® SPECIAL THINNER If our adhesives should dry a little bit in open containers, the adhesive can be adjusted again to brushing viscosity with the corresponding thinner.

• Re-positioning - the only covering film giving you a second chance without fear of colour-layer separation.
• Fuel-resistant - tolerates temperatures up to 250C and can be painted and is highly adhesive.
• Impeccable finish - follow the application instructions and there will be no bubbles and no sagging.
• Tough - made of genuine polyester ORACOVER is extremely tough and gives your model airplane additional stability. The patented polymerised multi-layer colour-bond is practically indestructible.
• Colour-fast - there is no 'bleeding' at the edges when ironing over seams.
• Foam-safe - can be applied to foam parts without problem as the specially formulated adhesive is already activated at only 80C.

• Brand: Oracover
• Part No: ORA521-102-002
• Barcode: 5051121145038
• Material: Oracover