The convenience and performance of brushless technology is available for everyone with the Photon Sensorless Waterproof System from Etronix. Simple to set-up and with a range of sensible KV rated motors for most r/c car applications and abilities the Photon is the ideal brushless start-up package or upgrade from a stock brushed set-up.An ideal choice for any 1/10th buggy, truggy, short course or truck application.
With the supplied programmable set up card (ET0107) the user can finely tune ten different parameters within the ESC to suit their particular needs.
When choosing your new ESC/ESC and motor combo, please take note of the relevant motor and battery cell count limits.
Royal mail at £3.95, or Express at £6.95.
Full details at checkout.
Some items cannot be sent via Royal Mail due to their restrictions.
To see shipping costs simply add the item to your basket and choose your country from the drop down list on the view cart page.
Yes it will fit, however we'd recommend a lower KV for a Slash.
Answered by: Ben @ Wheelspin Models
Answered by: Ben @ Wheelspin Models
This is ideally suited to 1:10 touring cars.
Answered by: Ben @ Wheelspin Models
This is a standard 1:10 scale system. The only model from your list we sell is the FTX Viper, which I can confirm this would physcially fit - however it's bit underpowered.
Answered by: Ben @ Wheelspin Models
Hmm, it's more suited to lighter vehicles.
For that truck we'd start with say ET0430
Answered by: Ben @ Wheelspin Models
We'd probably go for a lower KV such as the ET0420
As with any motor/ESC setup, always keep an eye on temperature and gear accordingly.
Answered by: Ben @ Wheelspin Models
We don't sell HSP so it's difficult for us to advise fully, however if your car takes standard 540 size motors (which is likely) then yes - this should fit.
As with any motor upgrade, it's important to keep an eye on temperatures and gear accordingly to avoid damage.
This combo comes with a program card.
Answered by: Ben @ Wheelspin Models
We'd reccomend a 2S LiPo. Something like VZ0317 would be ideal
Answered by: Ben @ Wheelspin Models
The stampede is a bit heavy for this, especially on 3S. You'd need to be looking at a much higher rated system to run 3S in that, something like perhaps HW38010200
Answered by: Ben @ Wheelspin Models
The motor has bullets on it, but they do not come with a battery connector.
Answered by: Ben @ Wheelspin Models
Yes this is a brushless upgrade
Answered by: Ben @ Wheelspin Models
This would be too powerful, you would need the Hobbywing Axe system.
Answered by: Anthony @ Wheelspin Models
This will physically fit but is probably a bit underpowered.
HW38010203 would be a better choice
Answered by: Ben @ Wheelspin Models
Yes this would be spot on for that car.
Answered by: Anthony @ Wheelspin Models
It would fit yes - but probably a bit underpowered. I'd look at say HW38010203 instead
Answered by: Ben @ Wheelspin Models
The motor shaft will be 3.2mm
Answered by: Si @ Wheelspin Models
The KV rating is the motor, so the motor KV is 4350, this means the motor will do 4350rpm for every 1 volt of power that it has, so if using a 7.4v 2s lipo 4350 x 7.2 = total RPM
Answered by: Si @ Wheelspin Models
Yes it will fit fine and run comfortably on 2s lipo.
Answered by: Steve @ Wheelspin Models
This will work for you yes, the ESC may be a litte large to find space for in the chassis, you could look at HW38020319 but this will require soldering
Answered by: Si @ Wheelspin Models
This will fit the 1/10th touring car no problem, this system is a 2s only system so will not run 3 or 4s lipo.
Answered by: Si @ Wheelspin Models