GBP
€ Euro
$ USD
Voltz 5000mAh Hard Case LiPo - 7.4V 2S 50C - Deans
Brand: Voltz
Part No: VZ0317
In Stock: Usually ships same day
VOLTZ 5000mah 2S 7.4V 50C HARDCASE LiPO STICK BATTERY PACK
Experience the rugged durability of Voltz RC LiPo power with this 5000mAh 7.4V 50C hard case lithium polymer battery suitable for all radio control vehicles. The hard shell provides extra protection for the battery, allowing the RCcar to be driven to its extremes whilst maintaining great power.p>
Specifications
- Capacity: 5000mah
- Voltage: 7.4v
- Max Cont. Discharge: 50c
- Max Burst Discharge: 100c
- Weight: 300g
- Dimensions (mm): 138x46x25
Declaration of Conformity
VZ0317 Declaration of Conformity
Secured by Stripe
- Brand: Voltz
- Part No: VZ0317
- Barcode: 5055323946998
- Voltage: 2S - 7.4v
- Connector: Deans (HCT)
- Case Type: Hard Case
- Fitment: Option Part
This item is also listed in the following additional categories:
Standard Shipping
£3.95 to most of the UK
Express Shipping
£6.95 to most of the UK
Worldwide Shipping
Available at checkout
Reviews
no complaints about this battery.
Excellent battery with matching cell resistance
I've been using this battery for the last 13 months in my HPI Jumpshot Flux (400kv brushless setup 2wd stadium truck), a TT02 with 17.5t brushless setup and an Associated MT10 (3300kv 4wd 1/10th monster truck). these are just bashing around my back garden/the park and never skate park style bashing. Unfortunately it has now started to puff and not balance charge correctly. It was always storage charged within 12 hours of use and always charged at 1C (5amps). Its not a bad service life but my Corally Sport racing pack i purchased at the same time used in the same cars is still going strong and balance charging quickly with low IR. Bottom line it was a decent cheap punchy battery while it lasted
WRITE A REVIEW
Questions & Answers
Yes that should be fine.
The dimensions are on the listing ;) 138x46x25mm
No, as your battery tray is the older round type design, you need a round case lipo where the leads come from the middle of one of the ends, something like this would work for you.
Yes that would work fine.
Yes, this will work for you but you will need a deans charge lead ET0268
Yes it will but it has a deans connector on it so you will need a deans to traxxas adaptor O-LGL-ADAPT16
Yes this would plug straight in to the side of the charger, You could if you wanted to, to give you more wire use a 2s balance extension lead like ET0245
That is the battery we recommend and the biggest that will fit, the carnage brushless is 2s lipo maximum so you cannot run 3s lipos im afraid.
Yes it will fit but the connector is different and the esc will need to be put into lipo mode.
Yes it will fit that will take around 8 hours on the original charger.
Yes they will fit.
Yes that should fit
No sorry you need a round case lipo for this chassis .
Yes that should fit a Savage XS
No these will be too large. V797311 looks to be the battery you need
Probably around 25 mins or so , depending on driving style
Afraid I don't know what that is sorry..
You'd be better with a round case pack eg C-49440 for a better fit
You'd be better with a round case pack eg C-49440 for a better fit
Yes these have standard xH balance leads
Yes they will work nicely with that
Yes that should fit
Yes it should fit
It will work yes, but i suspect you'd want something higher cell count and soft case
Yes that will fit
Maybe around 25 mins depending on how you drive.
Probably around 25-30 mins depending on driving style.
Around 25+ mins or so
2S cut off is 6v minimum
Yes, that will fit that car.
These have a deans connector, so you will either need to change the connector on your car or use an adapter.
Yes that would work
Yes
Yes this will work, just make sure to set the ESC to LiPo mode
Yes, it will work - just make sure your ESC is set to LiPo cut-off mode.
You will also need to either change the connector on your ESC to deans, or use an adapter such as ET0817
These come with a deans connector as pictured.
If your FMS plane has a deans then yes, that should connect fine.
Yes that will work with Carange brushless or Vantage brushless
ASK A QUESTION
For more in depth queries, please contact us.