GBP
€ Euro
$ USD
Oracover Air Medium 2M Chrome Blue (097)
Brand: Oracover
Part No: ORA321-097-002
Shadow Stock: Usually ships next day
Oracover Air Medium 2M Chrome Blue (097) is a lightweight, colour-fast polyester covering film designed for ultra-light model constructions where minimum weight is essential. This thermal-shrink AIR Medium variant is approximately 34 µm thick and is supplied as a 2,000 mm x 600 mm sheet. Part number: ORA321-097-002.
Key Features
- Colour-fast finish with no bleeding at seams when ironing.
- Optimised for light constructions such as indoor flyers, park flyers, blimps and airships.
- No adhesive layer on the film; apply ORACOVER AIR Hotmelt Adhesive to the surface before covering.
- AIR Medium thickness: approx. 34 µm.
Recommended Accessory
- ORACOVER AIR Hotmelt Adhesive (approx. productivity: 1 tin per ~1 m²).
- ORACOVER AIR Special Thinner (to restore brushing viscosity if adhesive thickens).
Application Overview
- Sand the wood and remove dust.
- Stir the adhesive thoroughly.
- Brush on 1–2 thin, even coats.
- Allow to dry at least 10 hours; do not resand.
- Apply ORACOVER AIR film with heat as usual.
- Note: Unsuitable for surfaces not resistant to organic solvents.
Specifications
- Colour: Chrome Blue (097)
- Material: Polyester
- Sheet size: 2,000 mm x 600 mm (approx. 78.74 in x 23.62 in)
- Manufacturer guidance: AIR Medium is intended for blimps and airships up to 4 m length.
- Brand: Oracover | Part number: ORA321-097-002
Secured by Stripe
Key Features
- Colour-fast - there is no 'bleeding' at the edges when ironing over seams.
-
The covering for light constructions.
Wherever minimum weight is demanded, wherever weight has to be reduced to its limits, ORACOVER® AIR is the product to be applied.
Whether indoor flyers, park flyers, blimps or airships are to be built, ORACOVER® AIR will do the covering job.
In contrast to regular ORACOVER®, ORACOVER® AIR has no adhesive layer.
The hotmelt adhesive is to be brushed onto the surface.
ORACOVER® AIR MEDIUM (approx.34 µm), for blimps and airships up to 4 m length.
RECOMMENDED ACCESSORY :
ORACOVER® AIR Hotmelt Adhesive ORACOVER AIR Adhesive (100 ml) Unstable wood fibres can become insecure and can rip off due to the weight. The consequences would be wrinkling and in the worst case the complete peeling off of the fabric.
Our tip: For an optimal pre-treatment of your wood surface we recommend to coat the surfaces to be ironed with ORACOVER® AIR Hotmelt Adhesive.
The ORACOVER® AIR Hotmelt Adhesive penetrates the wood and sticks together the loose wood fibres of the heartwood.
With that you reach an excellent three-D adhesion of the ORACOVER® AIR film with the surface.
With the ORACOVER® AIR Hotmelt Adhesive you do not need a further pre-treatment of the wood anymore.
Application of the ORACOVER® AIR Hotmelt Adhesive:
1. Sand your wood completely and remove the swarf (vacuum).
2. Stir up well the contents of the tin.
3. Apply the ORACOVER® AIR Hotmelt Adhesive 1 – 2 times thinly and evenly by using a brush.
4. Let the adhesive dry overnight, however at least 10 hours. (Please do not resand).
5. Cover your model as always with the thermal shrink fabric covering ORACOVER® AIR.
Productivity: approx. 1 tin / 1m² Unsuitable for surfaces which are not resistant to organic solvents.
ORACOVER® AIR SPECIAL THINNER If our adhesives should dry a little bit in open containers, the adhesive can be adjusted again to brushing viscosity with the corresponding thinner.
Weights & Dimensions
| Shipping Weight | 0.09kg | 0.20lbs |
| Product Width | 600mm | 23.62in |
| Product Length | 2,000mm | 78.74in |
- Colour: Chrome Blue
- Material: Polyester
Key Info:
- Brand: Oracover
- Part No: ORA321-097-002
- Barcode: 505112114480
- Material: Oracover
Standard Shipping
£3.95 to most of the UK
Express Shipping
£6.95 to most of the UK
Worldwide Shipping
Available at checkout
Reviews
No specific product reviews yet, why not write one?WRITE A REVIEW
ASK A QUESTION
For more in depth queries, please contact us.