GBP
€ Euro
$ USD
Oracover Air Medium 2M Chrome Lt-Green (095)
Brand: Oracover
Part No: ORA321-095-002
Out Of Stock
Request Stock NotificationOracover AIR Medium in Chrome Light Green (095) is a lightweight polyester thermal-shrink covering supplied as a 2,000mm x 600mm sheet. Designed for light constructions where minimum weight is critical, this ORACOVER AIR film is approx. 34 µm thick. Part no. ORA321-095-002.
Key Features
- Colour-fast finish with no bleeding at seam edges when ironing.
- Optimised for light constructions where minimum weight is required.
- Suitable for indoor flyers, park flyers, blimps and airships; AIR Medium referenced for blimps/airships up to 4 m length.
- No adhesive layer (unlike regular ORACOVER); apply ORACOVER AIR Hotmelt Adhesive to the surface before covering.
- Material: Polyester.
- Size: 2,000mm length x 600mm width.
- Colour: Chrome Light Green (095).
Recommended Accessory
- ORACOVER AIR Hotmelt Adhesive (100 ml): penetrates wood, binds loose fibres and promotes strong three-dimensional adhesion. Productivity approx. 1 tin per 1 m². Unsuitable for surfaces not resistant to organic solvents.
- ORACOVER AIR Special Thinner: restores brushing viscosity if the adhesive thickens in an open container.
Application Overview
- Sand the wood evenly and remove swarf (vacuum).
- Stir the hotmelt adhesive thoroughly.
- Brush on 1–2 thin, even coats.
- Allow to dry at least 10 hours or overnight; do not re-sand.
- Cover and heat-shrink with ORACOVER AIR as usual.
Secured by Stripe
Key Features
- Colour-fast - there is no 'bleeding' at the edges when ironing over seams.
-
The covering for light constructions.
Wherever minimum weight is demanded, wherever weight has to be reduced to its limits, ORACOVER® AIR is the product to be applied.
Whether indoor flyers, park flyers, blimps or airships are to be built, ORACOVER® AIR will do the covering job.
In contrast to regular ORACOVER®, ORACOVER® AIR has no adhesive layer.
The hotmelt adhesive is to be brushed onto the surface.
ORACOVER® AIR MEDIUM (approx.34 µm), for blimps and airships up to 4 m length.
RECOMMENDED ACCESSORY :
ORACOVER® AIR Hotmelt Adhesive ORACOVER AIR Adhesive (100 ml) Unstable wood fibres can become insecure and can rip off due to the weight. The consequences would be wrinkling and in the worst case the complete peeling off of the fabric.
Our tip: For an optimal pre-treatment of your wood surface we recommend to coat the surfaces to be ironed with ORACOVER® AIR Hotmelt Adhesive.
The ORACOVER® AIR Hotmelt Adhesive penetrates the wood and sticks together the loose wood fibres of the heartwood.
With that you reach an excellent three-D adhesion of the ORACOVER® AIR film with the surface.
With the ORACOVER® AIR Hotmelt Adhesive you do not need a further pre-treatment of the wood anymore.
Application of the ORACOVER® AIR Hotmelt Adhesive:
1. Sand your wood completely and remove the swarf (vacuum).
2. Stir up well the contents of the tin.
3. Apply the ORACOVER® AIR Hotmelt Adhesive 1 – 2 times thinly and evenly by using a brush.
4. Let the adhesive dry overnight, however at least 10 hours. (Please do not resand).
5. Cover your model as always with the thermal shrink fabric covering ORACOVER® AIR.
Productivity: approx. 1 tin / 1m² Unsuitable for surfaces which are not resistant to organic solvents.
ORACOVER® AIR SPECIAL THINNER If our adhesives should dry a little bit in open containers, the adhesive can be adjusted again to brushing viscosity with the corresponding thinner.
Weights & Dimensions
| Shipping Weight | 0.09kg | 0.20lbs |
| Product Width | 600mm | 23.62in |
| Product Length | 2,000mm | 78.74in |
- Colour: Chrome Light Green
- Material: Polyester
Key Info:
- Brand: Oracover
- Part No: ORA321-095-002
- Barcode: 505112114478
- Material: Oracover
Standard Shipping
£3.95 to most of the UK
Express Shipping
£6.95 to most of the UK
Worldwide Shipping
Available at checkout
Reviews
No specific product reviews yet, why not write one?WRITE A REVIEW
ASK A QUESTION
For more in depth queries, please contact us.