EUR
£ GBP
$ USD
Oracover Air Outdoor 2M Trans Red (029)
Brand: Oracover
Part No: ORA321-029-002
Shadow Stock: Usually ships next day
Oracover Air Outdoor 2M Trans Red (029) is a lightweight polyester thermal-shrink covering designed for minimum-weight constructions. Supplied in a 2,000mm x 600mm sheet in Transparent Red, this ORACOVER AIR OUTDOOR variant is approximately 23 µm thick and features colour-fast edges that resist bleeding when ironing seams. Unlike standard ORACOVER, ORACOVER AIR has no pre-applied adhesive and is used with a brush-on hotmelt adhesive for reliable bonding. Part number ORA321-029-002.
Key Features
- Colour-fast finish with no edge bleeding when ironing over seams.
- Ultra-light covering for weight-critical builds such as indoor flyers, park flyers, blimps and airships.
- Approx. 23 µm film thickness (ORACOVER AIR OUTDOOR).
- No adhesive layer on the film; apply ORACOVER AIR Hotmelt Adhesive to the surface.
- Also increasingly used as base material for model sails.
- Material: Polyester.
- Colour: Transparent Red (029).
- Unsuitable for surfaces not resistant to organic solvents.
Recommended Accessory
- ORACOVER AIR Hotmelt Adhesive – penetrates wood, consolidates loose fibres and provides excellent three‑dimensional adhesion between film and surface.
- ORACOVER AIR Special Thinner – restores brushing viscosity if adhesive thickens in an open container.
- Typical coverage: approximately 1 tin per 1 m² (as stated by the manufacturer).
Application Steps (Adhesive)
- Sand the wood surface thoroughly and remove swarf (vacuum).
- Stir the adhesive well.
- Brush on 1–2 thin, even coats.
- Allow to dry overnight (at least 10 hours). Do not sand again.
- Cover as usual with ORACOVER AIR thermal shrink covering.
Weights & Dimensions
- Width: 600 mm
- Length: 2,000 mm
- Shipping weight: 0.09 kg
Secured by Stripe
Key Features
- Colour-fast - there is no 'bleeding' at the edges when ironing over seams.
-
The covering for light constructions.
Wherever minimum weight is demanded, wherever weight has to be reduced to its limits, ORACOVER® AIR is the product to be applied.
Whether indoor flyers, park flyers, blimps or airships are to be built, ORACOVER® AIR will do the covering job.
In contrast to regular ORACOVER®, ORACOVER® AIR has no adhesive layer.
The hotmelt adhesive is to be brushed onto the surface.
ORACOVER® AIR OUTDOOR (approx.23 µm), the best choice for more solid light aircraft, park flyers, etc. ORACOVER® AIR OUTDOOR has not only proved itself as covering film for model airplanes, but becomes more and more popular as base material for model sails.
RECOMMENDED ACCESSORY :
ORACOVER® AIR Hotmelt Adhesive ORACOVER AIR Adhesive (100 ml) Unstable wood fibres can become insecure and can rip off due to the weight.
The consequences would be wrinkling and in the worst case the complete peeling off of the fabric.
Our tip: For an optimal pre-treatment of your wood surface we recommend to coat the surfaces to be ironed with ORACOVER® AIR Hotmelt Adhesive.
The ORACOVER® AIR Hotmelt Adhesive penetrates the wood and sticks together the loose wood fibres of the heartwood. With that you reach an excellent three-D adhesion of the ORACOVER® AIR film with the surface.
With the ORACOVER® AIR Hotmelt Adhesive you do not need a further pre-treatment of the wood anymore.
Application of the ORACOVER® AIR Hotmelt Adhesive:
1. Sand your wood completely and remove the swarf (vacuum).
2. Stir up well the contents of the tin.
3. Apply the ORACOVER® AIR Hotmelt Adhesive 1 – 2 times thinly and evenly by using a brush.
4. Let the adhesive dry overnight, however at least 10 hours. (Please do not resand).
5. Cover your model as always with the thermal shrink fabric covering ORACOVER® AIR.
Productivity: approx. 1 tin / 1m² Unsuitable for surfaces which are not resistant to organic solvents.
ORACOVER® AIR SPECIAL THINNER If our adhesives should dry a little bit in open containers, the adhesive can be adjusted again to brushing viscosity with the corresponding thinner.
Weights & Dimensions
| Shipping Weight | 0.09kg | 0.20lbs |
| Product Width | 600mm | 23.62in |
| Product Length | 2,000mm | 78.74in |
- Colour: Transparent Red
- Material: Polyester
Key Info:
- Brand: Oracover
- Part No: ORA321-029-002
- Barcode: 5051121144857
- Material: Oracover
Standard Shipping
£3.95 to most of the UK
Express Shipping
£6.95 to most of the UK
Worldwide Shipping
Available at checkout
Reviews
No specific product reviews yet, why not write one?WRITE A REVIEW
ASK A QUESTION
For more in depth queries, please contact us.