USD
£ GBP
€ Euro
Roto Start System - Fits Force/SH Engines
Brand: Fastrax
Part No: FT02623F
In Stock: Usually ships same day
Everything you need to get your shiny new electric model out on the road!
VZ0010
ORI30198DNS
Saves $5.11 over RRP
Looking for a step up from the basic package? Why not take a larger capacity battery coupled with a fast charger.
ET0208
SCH-EP3000S
Saves $9.35 over RRP
The Fastrax Roto Start System (FT02623F) provides an easy, consistent way to start your nitro R/C engine. Supplied with a Force/SH plate, it uses a powerful 550 motor and a 6mm shaft with hexball tip to engage the torque-slip backplate receptacle. The slip design helps protect components by disengaging if the engine locks.
Key Features
- Powerful 550 motor starter unit
- Supplied with Force/SH plate
- Torque-slip backplate reduces risk of damage on lock-up
- Uses a 6mm hex shaft with hexball tip
- Fits 12mm hex one-way bearing
- 27mm backplate hole spacing
- Suggested compatibility: Force/SH engines meeting the above dimensions
Tech Note
For best results, operate the starter in short, sharp bursts. Do not run continuously for more than 15 seconds at a time to help prevent heat build-up and potential gear damage.
Secured by Stripe
Fastrax Roto Start (with Force/SH Plate)
Start your nitro R/C engine effortlessly using this new Roto Start with powerful 550 motor. Insert the 6mm shaft with hexball tip into the new Torque-Slip design backplate receptacle to start your engine. The torque slip back plate features a specially design 'slip' unit to avoid possible damage should the engine lock up.
Fits 12mm hex one way bearing and features 27mm hole spacings
Tech Note: Starting any engine should be done in short, sharp bursts. These are NOT designed to be "held on" for more than 15+ seconds at a time - doing so will cause heat build up and gear damage.
Key Info:
- Brand: Fastrax
- Part No: FT02623F
- Barcode: 5055323911675
Standard Shipping
£3.95 to most of the UK
Express Shipping
£6.95 to most of the UK
Worldwide Shipping
Available at checkout
Reviews
Good service excellent quality
Great piece of kit and well made, will save all the blisters !!!! Amazing service and advice from Steve, top bloke !!!!
Great piece of kit. However on the carnage you will need to orient it so the starter sticks out to the drivers side as it were. You can put it inboard but the reinforcement arm for the rear axle won’t go back on. So use a 2.5mm drill and drill another hole also as if you have it with starter outward you’ll only have 2 screws holding the whole thing on so drill and use an M2 or M3 bolt and nut and it’s sorted.
WRITE A REVIEW
Questions & Answers
This fits the carnage NT.
Returns within 28 days are no problem, provided these are still in their sealed packaging please feel free to pop these back to us with one of our returns forms as attached.
You will need a 7.2v Nimh battery - we list a combo on our page that you can use for this.
This will use a standard 7.2 Nimh pack something like this VZ0010
Yes this should work on that engine
Yes, this will work as long as you have an SH engine.
It will not fit straight away and would require modifications so it is not something we recommend.
Yes it will fit.
Yes it is.
Not a model we sell - so I'm really not able to advise sorry
I don't think so sorry
Afraid not 100% sure on that - please check the dimensions listed at 
Yes, if you have a 12mm hex and an F series engine
No, sorry
No.
FAST565 can fit the Carnage with some modifications... So might fit the Torro, however - it's not something anyone here has tried or would recommend. We would therefore ere on the side of caution and say that they're not compatible.
No, but the FT02623H will work (if you have non COPS engine)
I can't confirm as we don't sell that model - but please check dimensions shown in our image at https://wheelspin.s3.eu-west-2.amazonaws.com/img/FT02623F-a1f2.jpg
Possibly - dimensions are as shown in the image at https://wheelspin.s3.eu-west-2.amazonaws.com/img/FT02623F-a1f2.jpg
Sorry but no we don't have one
Afraid there's nothing that I know to that will fit that.
You would be better looking at a starter box such as FAST555
It will fit Force/SH engines.... If you truck has one of those with the dimensions listed - it should fit.
If you have the G3.0 engine then yes I believe this will fit
Now added an image to show the dimensions on this :-)
No it won't sorry
Force .46 isn't one we've tried... If it's a Force 4.6 (4.6cc) then that should fit based on our experience.
It's unlikley to fit that sorry.
It's unlikely to fit, sorry.
It will, but there is work to be done to make it work.
It will bolt onto the engine with no issues at all, but, the backplate hits the chassis, so the engine has to be shimmed up around 2mm, not a job for a novice, bit it is achievable
Yes it should fit.
No, this won't fit the Schumacher
No, the Hellfire had a K series engine so needs HPI Roto start HPI-87148
No, you'd want the Hobao version FT02623H
This is listed as fitting SH engines, so whilst we haven't tried it ourselves, we believe so yes.
We don't have that engine here to try - however it's very doubtful.
Hmm, it's doubtful - it will only fit Force engines.
Doubtful, unless it has a retro-fitted Force engine.
I believe so, but we're not 100% sure as we don't sell that engine.
Yes, this includes backplate and the hand unit.
Yes it should do.
I believe it's for the larger SH engines only.
ASK A QUESTION
For more in depth queries, please contact us.